SUNLU 2000G ABS Like Resin For 3D Printer, 405nm UV Curing Photopolymer Rapid 3D Resin For 2K 4K 6K 8K LCD/DLP/SLA 3D Printers, Non-Brittle & High Precision & Low Shrinkage, 2KG, Grey

Good consistent resin. Not as strong or as flexible as some but a good overall material. I use it for testing and prototyping parts that will later be printed with more appropriate material or manufactured by other means.

This is a great all-around resin. It may not do everything perfectly, but does most things well. The pictures are of some of my prints, I have done very little to clean these up other than removing the supports and assembling the car (wheels were separate). This material is tuf. The ball can be thrown, bounced, and beaten. I have printed a couple and plan on trying a couple bats on some of them. I don't image it would struggle with a wiffle ball bat, but I doubt it will survive a metal or wood bat.Note: Thin pieces, such as the sword held by the biker punk, are flexible. I printed a bookmark for my sister (Sorry no pictures) and the part that went in the book was very thin and very flexible, but still seemed durable.I have only had one print failure, but I have failed to get that particular model to print with any resin.I have only had a 3D printer for a month or so at this point, I have tried a few resins. This one is the best and the price is right.

I make my own 3D models that I print and use to make jewelry and cosplay items for my etsy store. My typical go-to resin is Elegoo standard in gray, it has always performed very well for me and I'm not someone to often decide to try something else when what I have does what I need it to. Then I wanted to try out a white resin to make some buttons for kandi this past weekend and this was the brand that I could get the fastest (and I believe the cheapest too but I don't really remember).My printer is an Elegoo Saturn, models sliced in chituboxPro and chitubox basic. I could not find any information on print settings so I figured let's just try my typical ones, which are the base elegoo resin settings from their spreadsheet with only modifying the layer height from 0.05mm to 0.04mm, the bottom lift speed to 40mm/min and lifting speed to 50mm/min. The first batch of masks came out with some holes in cheeks which I attribute to a combination of needing a slightly longer exposure time and messing with the model a bit to adjust the thinner sections. Exposure time was brought up from 2.5s to 2.85s and this current batch came out great. My model is still very thin but the resin flexes a lot, my only concern with that is I have to be careful getting the supports off because the uncured model has a tendency to tear if I'm being rough with it. As for accuracy, the nominal width is 15mm and I've measured them at between 14.98-14.99mm so I'm pretty happy with that.It also seems to clean up pretty easily, though I do move my build plates after printing to allow as much resin to drip off as I can (sometimes overnight, or longer if I forget about them...) then do a quick initial rinse and light scrub in 99% IPA the a 4-5min run in clean IPA. Didn't need to run them through a 2nd wash cycle like I do with elegoo's abs-like 2.0 resin.My one and only gripe with it is that the white yellows pretty noticeably when curing. The above photo has an uncured model on the left(ish) and cured model on the right. Cured for 3 minutes in a Mercury XL cure box.Will definitely be trying out some more resins from Sunlu, I like what I've seen so far.

This resin has great detail, easy to print with, plenty of print profiles in lychee slicer, doesn’t smell too bad (for a resin) and is great value. Never had one leak in transit and is not brittle when cured like other brands or models.Parts stay flat when cured and are pretty accurate. Can drop parts and they generally hold up ok.Have printed a new trigger for my vacuum cleaner and is going on a year without breaking like the original ABS molded one.

i have tested a lot of resins from elegoo reprapper flashforge surayatech and so on . This by far outperforms them in the smelliness department. Its baarely noticeble. the strengh is good too. Prints can be broken but the wont break as easy as other waterwashables. Print speed is adequate too.The bad: Pricier than others ( not siraya tech). Not for functional parts. I found that the warping and dimentional accuracity is not on par with alcohol washed resins. So dont buy for that. For miniatures, absolutely fine resin.

I purchased this Water-Wash ABS Dark Grey resin hoping to replace the Space Grey color from Elegoo. The print quality seems really good and the parts do seem more durable. however I was really hoping the Dark grey would actually be dark but its fairly light grey which was disappointing because I was intending to use the resin for a certain project that needed a dark grey color that I wont be able to use it for now. Other than the color being way lighter shaded the resin seems to perform great and seems very durable with some slight flex